Number of copies set. Currently selected items appear in brackets. Selection keys 2. Example: initial copy display Press to cancel an operation or return to the previous display. Scroll keys Press to move the cursor to each direction one by one. Page 17 Turning On the Power This machine has two power switches.
When the machine has finished warming up, you can operate the machine. Turning On the Power A Press the operation switch. The On indicator goes on. When this is done, machine power is completely off. See General Settings Guide. If it is off, turn it on. B Turn on the main power switch. The main power indicator goes on. Doing so may result in damage to the memory, leading to malfunctions. B Press the operation switch. The On indicator goes off. Doing so may result in damage to the memory.
Not doing this may result in damage to the memory. A Be sure the On indicator is not lit. B Turn off the main power switch. The main power indicator goes out. Place them on the exposure glass instead. Place these originals on the exposure glass instead. If not, the image may not be copied properly.
See p. Not taking this precaution could cause marks on the exposure glass that will be copied onto paper. If you do, the ARDF cover might open or be damaged. B Place the original face down on Original Orientation You can set the original orientation in the following ways. This function is useful for copying torn or large originals. It should be aligned with the rear left corner.
However, some copy functions may produce different results depending on the orientation of the originals. For details, see the explanations of each function. Positioning mark 2. A Set the document guide to the original size. When copy paper size and original size differ, you need to specify the original size as follows: A Place originals face down on the exposure glass, or face up into the ARDF. ARK21S 1. Limit mark 2. When the regular size originals settings are registered, appears at the top of the copy display.
When the custom size originals settings are registered, appears on the top of copy display. The machine is ready to copy. B Make sure "d Ready" appears on the display. Copying starts. C Make sure no previous settings remain. D Place your originals. Reference See the explanations for each function.
The maximum number of sheets should not exceed the upper limit. Paper guide release lever Page 29 Copying from the Bypass Tray C Insert the paper with the side you want to copy facing down, and then adjust the paper guide with the paper size.
E Select the paper size and type. Horizontal size 2. Vertical size 3. Extender 4. D Pull down the paper guide release lever step B. The bypass tray is selected on the display.
If you require darker or lighter copies, adjust image density accordingly. The selected tray and the paper size appear. Base point when placing on the exposure glass. Base point when placing in the ARDF. Reference Related default settings p. B Press [Reduce] or [Enlarge]. When the original is placed on the exposure glass, the upper left corner is the base point.
When placed in the ARDF, the bottom left corner is the base point. B Press [Zoom]. C Enter the ratio. To enter the ratio using the number keys A Enter the desired ratio using the number keys. Page 35 Copier Functions Sort You can scan originals into memory and automatically sort copies.
When placing originals in the ARDF, set the first page on top. Changing the number of sets You can change the number of copy sets during copying. B Enter the number of copy sets using the number keys. C Place your originals. B Press [Sets].
C Enter the number of copy sets with the number keys, and then press [Resume]. Copying starts again. E Place your originals. If it was not specified for, proceed to step E. If it was not specified for, proceed to step D. Front 2. If it was not specified for, proceed to E. D When 1. You can separately copy the front and back of a two-sided original or two facing pages of a bound original onto two sheets. If other messages appear, follow the instructions as they are displayed. Message Causes Solutions Cannot dup.
Select one of these sizes. You can change the maximum copy quantity. Cannot sort this size A paper size not avail- Use copy paper of length unable with the Sort func- der mm. Size error in Combine mode A paper size not avail- Use copy paper of length unable with the Combine function has been specified. Image density is too dark. Adjust the image density. The reverse side of an orig- Image density is too dark. A shadow appears on copies if you use pasted originals.
Change the orientation of the original. Put mending tape over the pasted areas. The same copy area is dirty whenever making copies. The exposure glass or ARDF is dirty.
Clean them. Copies are too light. Image density is too light. The paper size is not appropriate. Use the recommended paper.
Toner bottle is almost empty. Add toner. Selected forums Clear. Filter : All threads. All threads. Proposed answers. General discussion. No replies. Has code. All languages. Sort : Relevance. Found threads. Archived Forums. When the user selects colour File Services and Storage.
Miguel Fra Falcon IT. Hi, I installed win 7 64 but it is not adapting with the printer drivers CD ROM, I tryed to download pcl6 drivers but it marking print error. Please help me. Learn more. Please select your local Ricoh website Ricoh Group operates in approximately countries and regions with a headquarter in Tokyo, Japan.
Seeking to Create New Values The Ricoh Group is making headway in a wide range of fields by combining our manufacturing technologies over the years with new technologies and ideas. What can Ricoh do for you? The value we provide today and into the future to our customers. About Ricoh. Living up to Expectations through Technology Through innovation, we continue to create technologies and products that help solve social issues.
0コメント